kode erorr canon IX4000/5000

Alarm LED
blinking in
orange
Error [Error code] Solution Remarks
2 times No paper. (ASF) [1000] Set the paper in the ASF, and
    press the Resume/Cancel
    button.
3 times Paper jam. [1300] Remove the jammed paper, and
   press the Resume/Cancel button.
   Error in paper feeding from the ASF.
   Paper output support error. [1300] Remove any obstacles, if any,
   from the paper output support,   and press the Resume/Cancel button.
  The first time the phenomenon occurs, it is indicated as the
   paper output support error. The second time and thereafter
   (such as when the phenomenon persists even after the
   Resume/Cancel button is pressed), it is indicated as the PS
   cam sensor error (service call error).
4 times No ink. [1600] Replace the empty ink tank(s),
   or press the Resume/Cancelbutton.
   Pressing the Resume/Cancel button will exit the error
   without ink tank replacement, however, ink may run out during printing.
   Ink tank not installed. [1660] Install the applicable ink tank(s) properly, and confirm that the
   LED's of all the ink tanks light red.
5 times The print head is not installed [1401],
   or it is not properly installed (Print
   head temperature sensor error
   [1403] / Faulty EEPROM data of the
   print head [1405]).
   Install the print head properly.
7 times Multiple ink tanks of the same color installed. [1681]
Replace the wrong ink tank(s)
with the correct one(s).
Ink tank in a wrong position. [1680] Install the ink tank(s) in the
correct position.
8 times Warning: The waste ink absorber
becomes almost full. [1700]
Pressing the Resume/Cancel
button will exit the error, and
enable printing.
The service call error, indicating the waste ink absorber is
full, is likely to occur soon.
9 times The connected digital camera or
digital video camera does not support
Camera Direct Printing. [2001]
Remove the cable between the
camera and the printer.
11 times Failed in automatic print head alignment. [2500]
Press the Resume/Cancel button.
    - If paper is being fed at error occurrence, the error is indicated after the paper is ejected.
    - If the error occurs, the print head alignment values are not changed.
    - After exit from the error by the Resume/Cancel button, the automatic print head      alignment  will   not be re-done. The error is indicated when the pattern is not printed due to
no ink or non-ejection of ink, or when the sensor's AD
value is incorrect.
13 times The remaining ink amount unknown. [1683]
An ink tank which has once
been empty is installed. Replace
the applicable ink tank with a new one.
Printing with a once-empty or refilled ink tank can damage the print head.
To continue printing without replacing the ink tank, press
the Resume/Cancel button for 5 sec. or longer to record the
use of a refilled ink tank.
Note:
After the above operation, the function to detect the
remaining ink amount is disabled. 14 times Ink tank not recognized. [1684] A non-supported ink tank is installed (the ink tank LED is turned off). Install the supported ink tanks. 1-4
2-2. Service Call Errors (by Cyclic Blinking in Orange (Alarm LED) and Green (Power LED), or Alarm LED Lit in Orange) 15 times Ink tank not recognized. [1410 to1419]
An error occurred in an ink tank (the ink tank LED is turned off). Replace the ink tank(s).
Access cover open. [1200] Close the access cover.Cycles of blinking in orange (Alram LED) and green (Power LED) Error [Error code] Solution (Replacement of listed parts, which are likely to be faulty)
2 times Carriage error [5100] - Carriage unit (QM2-3361)
     - Timing slit strip film (QC1-8750)
     - Logic board ass'y (QM2-3393 / QM3-1654)*1
     - Carriage motor (QK1-1500)
3 times Line feed error [6000] - Timing sensor unit (QM2-2683)
    - Timing slit disk film (QC1-4375)
     - Feed roller ass'y (QL2-1291)
     - Platen unit (QM2-3353)
     - Logic board ass'y (QM2-3393 / QM3-1654)*1
     - Paper feed motor (QK1-1996)
4 times Purge cam sensor error [5C00] - Purge unit (QM2-3370)
    - Logic board ass'y (QM2-3393 / QM3-1654)*1
5 times ASF (cam) sensor error [5700] - Sheet feed unit (QM2-3367)
6 times Internal temperature error [5400]
    - Logic board ass'y (QM2-3393 / QM3-1654)*1
7 times Waste ink absorber full [5B00]
     - Ink absorber kit (QY5-0164)
8 times Print head temperature rise error [5200]
    - Print head (QY6-0064)
    - Logic board ass'y (QM2-3393 / QM3-1654)*1
9 times EEPROM error [6800] - Logic board ass'y (QM2-3393 / QM3-1654)*1
12 times PG position error [5C10] - Sheet feed unit (QM2-3367)
    - Logic board ass'y (QM2-3393 / QM3-1654)*1
    - Purge unit (QM2-3370)
13 times AH position error [5710] - Sheet feed unit (QM2-3367)
    - Logic board ass'y (QM2-3393 / QM3-1654)*1
     - Output support unit (QM2-3358)
     - Output support gear unit (QM2-3359)
14 times PS cam sensor error [5750] - Sheet feed unit (QM2-3367)
     - Logic board ass'y (QM2-3393 / QM3-1654)*1
      - Output support unit (QM2-3358)
      - Output support gear unit (QM2-3359)
15 times USB Host VBUS overcurrent [9000] - Logic board ass'y (QM2-3393 / QM3-1654)*1
16 times Valve sensor error [6C00]
      - Logic board ass'y (QM2-3393 / QM3-1654)*1
      - Purge unit (QM2-3370)
17 times Motor driver error [6D00]
      - Logic board ass'y (QM2-3393 / QM3-1654)*1
19 times Ink tank position sensor error [6502]
      - Platen unit (QM2-3353)
      - Logic board ass'y (QM2-3393 / QM3-1654)*1
20 times Other hardware error [6500]
      - Logic board ass'y (QM2-3393 / QM3-1654)*1Continuous alternate blinking

jadi kesimpulanya 80% berada di bagian locig board./ mainboardnya utama penyakitnya
semoga dapat membantu keterangan diatas walaupun agak susah dimengerti hal bahasanya.